would not work even if you could “fit it in” - and the DIMM slots for the two are not physically/mechanically compatible either: don't try to force it in, or you might damage the slot, the DIMM … first 16GB DDR3 UDIMM & SO-DIMM modules. Diskutiere und helfe bei UDIMM Ram in DIMM Slot? @AshleyAshes there have been SO-DIIM to DIMM adapters long before DDR3 was even released. the win32_physicalMemory doesn't seem to provide this info ?. This 4GB (1x 4GB) DDR3 1333 MT/s RAM module from Samsung is for use in DDR3 compatible systems and operates at 1333 MT/s with an overall transfer rate of PC3-10600.. I wont be overclocking the ram so the heatsinks would have been of no use. Joined Dec 19, 2013 Messages 11. My desktop is in transit and I wanted to start researching upgrade options, and I don't want to mix my DIMM types to avoid any possible problems. The DDR4 key notch is in a different place, and the edge connector looks like a slightly curved “V” to facilitate insertion.
Since the ECC SO-DIMM form factor is an alternative solution that is often considered in the Embedded market this paper will look at all the aspects of preparing for and designing an Embedded system with ECC SO-DIMMs instead of using the traditional DDR3 UDIMM or SO-DIMM memory. Active 7 years, 4 months ago. I elected to purchase my model with [16GB DDR4-2133 DIMM (2x8GB) RAM]. And I would expect 1 16GB UDIMM to be more expensive than an 16GB REC ECC because the UDIMM has to use chips that are 2 times as dense. 1 of 2 Go to page. im Bereich Computerfragen im SysProfile Forum bei einer Lösung; UDIMM Ram in DIMM Slot? It is not electrically compatible - i.e.
*I want to buy low profile ram so i can easily install a bulky cooler. Go. I assume it's either UDIMM or RDIMM, but I can't be sure. If you need a lot of ram in your say "Xeon E3" server that only takes ecc unbuff, instead of spending $1600 or more, you'd be better off and buying a $1000 server that takes ecc/reg. Do you know any way to programaticaly get this info ? you can find more info about udimm rdimm here. Physically, a DDR4 module, or dual in-line memory module (DIMM), looks very similar to a DDR3 DIMM. Viewed 4k times 1. A memory rank is a set of DRAM chips connected to the same chip select, which are therefore accessed simultaneously.In practice all DRAM chips share all of the other command and control signals, and only the chip select pins for each rank are separate (the data pins are shared across ranks).. A DIMM or dual in-line memory module comprises a series of dynamic random-access memory integrated circuits.These modules are mounted on a printed circuit board and designed for use in personal computers, workstations and servers.DIMMs began to replace SIMMs (single in-line memory modules) as the predominant type of memory module as Intel P5-based Pentium processors began to … I just found that the first 16 Gigabyte "unbuffered" DDR3 DIMMs and also SO-DIMMs are now available from I'M Intelligent Memory, website: www.intelligentmemory.com They are …
UDIMM Ram in DIMM Slot?
However, DDR4 has 288 pins compared with DDR3’s 240 pins; DDR4 SO-DIMMS have 260 pins instead of 204 in DDR3. My desktop is in transit and I wanted to start researching upgrade options, and I don't want to mix my DIMM types to avoid any possible problems. Samsung 4GB (1x 4GB) CL9 DDR3-1333 PC3-10600 1.5V 240-pin UDIMM RAM Module - available now at ramcity.com.au for $57.99. So we have a single interposer that can be used to basically test both unbuffered and buffered DIMMs. is there a way to know if installed memory is Registered DIMM or Unregistered DIMM ? I assume it's either UDIMM or RDIMM, but I can't be sure.